自上料搅拌车安装与拆卸过程的注意事项_常见问题_全自动上料搅拌机车_自动上料搅拌机厂家-山东山汽工程机械有限公司

常见问题

热点

自动上料搅拌机配件是由哪两部分组成的？

2022-12-23

修路有哪些不错的机械设备？先说说这个小型搅拌车

2022-12-19

自上料搅拌车操作须知的五项重要内容

2022-12-16

自上料拌和车的特征有哪些？

2022-12-12

自动上料搅拌车能哪些施工难题？

2022-12-02

混凝土搅拌车的刹车片要怎样挑选合格

2022-11-14

关于山汽

联系人：刘老师

电话：400-879-1999

公司：山东山汽工程机械（集团）有限公司

地址：山东省莱州市206国道与308省道交叉口东南50米

自上料搅拌车安装与拆卸过程的注意事项

所属分类：常见问题发布时间：2022-09-28 来源：http://www.shanqijituan.com 浏览量：0

自上料搅拌车轴承的安装、拆卸方法，应根据轴承的结构、尺寸大小和与轴承部件的配合性质而定。安装、拆卸的压力应直接加在紧配合的档圈端面上，不能通过滚动体传递压力。

The installation and removal method of the bearing of the self feeding mixer truck shall be determined according to the structure, size and matching nature of the bearing. The installation and removal pressure shall be directly applied to the end face of the tight fitting retainer ring, and the pressure shall not be transmitted through the rolling element.

因为这样会在轴承工作表面造成压痕，影响轴承正常工作，甚会使轴承损坏。轴承的保持架、密封圈、防尘盖等零件很容易变形，安装或拆卸轴承的压力不能加在这些零件上。自上料搅拌车生产厂家

This will cause indentation on the working surface of the bearing, affect the normal operation of the bearing, and even damage the bearing. The cage, seal ring, dust cover and other parts of the bearing are easy to deform, and the pressure for installing or disassembling the bearing cannot be applied to these parts. From the manufacturer of charging mixer truck

轴承内圈与轴是紧配合，外圈与壳体为较松配合，可用压力机将轴承先压装在轴承上，然后将轴连同轴承一起装入壳体中，压装时在轴承端面上垫一软金属材料的装配套管（铜的或软钢管）。

The inner ring of the bearing is closely fitted with the shaft, and the outer ring is loosely fitted with the housing. Press the bearing onto the bearing with a press, and then install the shaft and the bearing into the housing. When pressing, pad a soft metal assembly sleeve (copper or soft steel pipe) on the end face of the bearing.

自上料搅拌车厂家认为，轴承内圈与轴，外圈与壳体孔都是紧配合，装配套管端面应做成能同时压紧轴承内外套圈端面的圆环，或用一圆盘和装配套管，使压力同时传到内外圈上，把轴承压入轴上和壳体中。此种安装方法特别适用于能自动调心的向心球面轴承的安装。

According to the manufacturer of the loading mixer truck, the inner ring of the bearing and the shaft, and the outer ring and the housing hole are closely matched. The end face of the assembly sleeve should be made into a ring that can compress the end face of the inner and outer rings of the bearing at the same time, or a disc and the assembly sleeve should be used to make the pressure transfer to the inner and outer rings at the same time, so as to press the shaft into the shaft and the housing. This installation method is especially suitable for the installation of radial spherical bearing with automatic centering.

上一页：为大家带来怎么区分自动上料搅拌车滤芯好坏下一页：控制好水泥自上料搅拌机设备用水量的方法