山东山汽工程机械(集团)有限公司
热线电话:400-879-1999 山汽微信
郑重声明 购机 售后
在线询价
热线电话:400-879-1999
您现在所在的位置: 首页> 新闻资讯 > 公司新闻

自动上料搅拌机在运输中应该注意什么?

所属分类:公司新闻 发布时间:2020-12-10 来源:http://www.shanqijituan.com 浏览量:0

1、蓄电池的保养检查:检查蓄电池固定是否牢固。
1. Battery maintenance inspection: check whether the battery is fixed firmly.
2、轮胎的检查:每月应在常温下检查一下轮胎气压。
2. Tire inspection: check the tire pressure at room temperature every month.
3、离合器总泵液面的检查:离合器液面介于高、低液面间则表示正常,如果低于标准线,则可能是总泵或分泵皮碗损坏。
3. Inspection of clutch master cylinder liquid level: if the clutch liquid level is between high and low, it means that it is normal. If it is lower than the standard line, it may be that the master cylinder or the cylinder cup is damaged.
4、制动液面的检查:制动也在高、低位之间则表示正常。
4. Check the brake fluid level: if the brake is between high and low, it means normal.
5、发动机冷却液液面检查:发动机在热机状态时,千万不要打开散热器盖,否则可能会被溅出的冷却液或高温蒸气烫伤。等发动机冷却后,检查冷却液的液面应处于满位和低位之间,否则应加蒸馏水或纯净水或冷冻液,加水后的液面高度不能超过满位。如发现短时间内冷却液减少的很快搅拌,自动上料搅拌车检查步骤应检查冷却系统是否有泄漏或到维修站去检查。
全自动上料搅拌车
5. Check the engine coolant level: when the engine is in hot state, do not open the radiator cap, otherwise it may be scalded by the splashed coolant or high temperature steam. After the engine cools down, check that the coolant level should be between the full level and the low level. Otherwise, distilled water or pure water or refrigerant should be added. The liquid level after adding water should not exceed the full level. If it is found that the coolant decreases rapidly in a short period of time, the automatic feeding mixer should check whether there is leakage in the cooling system or go to the maintenance station for inspection.
自动上料搅拌机操作环境通常都不是很好,这也导致需要我们对设备在操作之前有详细的了解才行。在确保设备不存在有任何故障问题之后才能够操作使用设备正常运行,避免在操作中可能存在的各种不良问题。
The operating environment of automatic feeding mixer is usually not very good, which also leads to the need for us to have a detailed understanding of the equipment before operation. After ensuring that the equipment does not have any fault problems, it can be operated and used normally, so as to avoid all kinds of bad problems that may exist in the operation.
我们在运输自动上料搅拌机的时候要考虑好道路的颠簸问题,因为往往我们运输过程中发现,很多司机都会采取紧急刹车跟紧急制动等操作,也往往是因为这些操作导致我们的自动上料搅拌一体机发生碰撞跟侧滑,所以我们在发货的时候一定要好好的嘱咐我们的司机师傅,要小心去运输,这样一来就避免出现很多问题。
When we transport the automatic feeding mixer, we should consider the bumpy problem of the road, because we often find that many drivers will take emergency braking and emergency braking and other operations, which often lead to collision and sideslip of our automatic feeding mixer. Therefore, we must give our company good instructions when delivering the goods Machine master, to be careful to transport, so as to avoid many problems.

 

首页 产品 电话 置顶