山东山汽工程机械(集团)有限公司
热线电话:400-879-1999 山汽官方微信
郑重声明 购机 售后
在线询价
热线电话:400-879-1999
您现在所在的位置: 首页> 新闻资讯 > 公司新闻 >

自动上料搅拌机延长使用寿命的方法

所属分类:公司新闻 发布时间:2021-05-17 来源:http://www.shanqijituan.com 浏览量:18

1、对于新购入的车辆,初次使用50小时左右,就该检查各处螺栓紧固情况。包括罐体封头与减速机的连接螺栓,减速机底座与前台的连接螺栓,拖轮底座与机架的连接螺栓,以及副梁与大梁的连接螺栓等。以后要保证每月定期检查一次。
1. For newly purchased vehicles, if they are used for about 50 hours for the first time, it is necessary to check the tightening of bolts. It includes the connecting bolts between the tank head and the reducer, the connecting bolts between the reducer base and the front stage, the connecting bolts between the tugboat base and the frame, and the connecting bolts between the auxiliary beam and the girder. In the future, it is necessary to ensure regular inspection once a month.
2、我们应该至少每月一次清理托轮和滚道上的污物;通过托轮上的油嘴,向托轮内注入润滑油脂。而且一定要保证传动轴至少每月润滑一次。
2. We should clean the dirt on the roller and raceway at least once a month; The lubricating grease is injected into the supporting roller through the oil nozzle on the supporting roller. And make sure that the transmission shaft is lubricated at least once a month.
自动上料搅拌机
3、液压系统部件,这个地方的精度较高。尤其是搅拌车液压泵,保养简易,但要求很高。液压油要定期更换,运行500小时,以后2000小时或至少每年更换一次,滤芯应该同时更换。切记在加油或换油时发动机必须处于停止状态,否则将造成液压系统损坏。
3. Hydraulic system components, this place has high precision. In particular, the mixer hydraulic pump is easy to maintain, but the requirements are very high. The hydraulic oil should be changed regularly, the first 500 hours, after 2000 hours or at least once a year, the filter element should be changed at the same time. Remember that the engine must be stopped when refueling or changing oil, otherwise the hydraulic system will be damaged.
4、每天行车前检查托轮与滚道的结合面润滑油是否干涩,应及时补充,保持良好的润滑效果。每次在车辆发动之前,检查冷却器和减速机的油位,保证油位指示在目视范围内;检查液压油路的密封情况,保持液压系统清洁和密封,以免尘粒和水份等污染系统液压油,造成系统不能正常工作或损坏。
4. Every day before driving, check whether the lubricating oil on the joint surface of the roller and the raceway is dry, and replenish it in time to maintain a good lubricating effect. Every time before the vehicle starts, check the oil level of the cooler and reducer to ensure that the oil level indication is within the visual range; Check the sealing condition of the hydraulic oil circuit, keep the hydraulic system clean and sealed, so as to avoid dust particles and water polluting the hydraulic oil of the system, causing the system not to work normally or damage.
热门产品 / HOT PRODUCT

 

首页 产品 电话 置顶