你对自动混凝土搅拌机很熟悉，今天我想跟你解释一下全自动上料搅拌机卸料时需要注意的问题，希望你在工作时注意。
You are very familiar with the automatic concrete mixer. Today, I want to explain to you the problems that need to be paid attention to when unloading the full-automatic loading mixer. I hope you pay attention to them when working.
1、进入现场时要尽量走在中间:现场道路简单，路基松软，现在搅拌车要做20多辆，靠近路边时，路面容易被压碎和塌陷，导致车辆翻倒。
1. When entering the site, try to walk in the middle: the road on site is simple and the subgrade is soft. Now there are more than 20 mixers. When approaching the road, the road surface is easy to be crushed and collapsed, resulting in vehicle overturning.
2,提前下车检查:混合卡车大多是在夜间,网站,更好是手电筒,下车检查线,有障碍,坑或更软的地方,必须记住,满足钢钉的时间清理。
2. Get off the vehicle for inspection in advance: most of the hybrid trucks are at night, on the website, it's better to use flashlight, get off the vehicle inspection line, there are obstacles, pits or softer places, and it must be remembered to meet the requirements of steel nail cleaning time.
3,混凝土罐车必须缓慢倒车时,并不总是把你的头伸出窗外,看后视镜的两边,如果不确定,停下来看清楚扭转之前,很多路是挖掘机就软了,车子很容易下沉。开始,缓慢而均匀的速度开车,扭转路线尽可能直,如果你想重复下了车,方向盘不杀死或玩,在柔软的道路容易拖延,节流阀,速度太快,撞上东西。
3. When the concrete tank truck has to reverse slowly, it doesn't always put your head out of the window and look at both sides of the rear-view mirror. If you are not sure, stop and see clearly before reversing, many roads are soft with excavators, and the car is easy to sink. At first, drive slowly and evenly, and turn the route as straight as possible. If you want to get off the car repeatedly, the steering wheel will not kill or play. It is easy to delay on the soft road, throttle valve, speed is too fast, and hit things.
全自动上料搅拌机卸料时应注意的问题:
The problems that should be paid attention to when unloading the full-automatic feeding mixer:
1. 在卸料前，让搅拌槽全速运转一两分钟，使混凝土充分混合。如有必要，可加水，使混凝土拌合更加均匀，便于排出。
1. Before discharging, allow the mixing tank to run at full speed for one to two minutes to fully mix the concrete. If necessary, water can be added to make the concrete mix more even and easy to discharge.
2. 卸料时，尽量将车停在地面上，并在卸料前将卸料料斗溜槽弄湿，以便清洗。
2. When unloading, park the vehicle on the ground as much as possible, and wet the chute of discharge hopper before unloading, so as to facilitate cleaning.
3.喂奶时更好注意自己，不要随意操作喂奶杆。油箱每次绕中间座转动时更好停车，以保护减速机和支撑轮。
3. It is better to pay attention to yourself when feeding, and do not operate the feeding rod at will. It is better to stop the oil tank every time it rotates around the middle seat to protect the reducer and supporting wheel.
4、清洗锅时一定要仔细冲洗干净，并将水反复正反转两遍，然后放出去，一次要把水箱中的所有水倒入锅内，然后返回站加水彻底清洗锅内。
4. When cleaning the pot, you must wash it carefully, turn the water forward and backward twice, then put it out, pour all the water in the water tank into the pot for the last time, and then return to the station to add water to clean the pot thoroughly.
全自动上料搅拌机卸料时必须注意以上几点，如果做得不好，可能会造成贮槽封闭的现象。我希望你注意听了。
The above points must be paid attention to when the full-automatic feeding mixer is discharging. If it is not done well, it may cause the phenomenon of tank sealing. I hope you pay attention.
山汽微信
2022-12-23
首页
产品
电话
置顶