山东山汽工程机械(集团)有限公司
热线电话:400-879-1999 山汽官方微信
郑重声明 购机 售后
在线询价
热线电话:400-879-1999
您现在所在的位置: 首页> 新闻资讯 > 行业新闻 >

作为自动上料搅拌车管理者需要知道的事项

所属分类:行业新闻 发布时间:2022-04-27 来源:http://www.shanqijituan.com 浏览量:18

作为自动上料搅拌车管理者需要知道的事项
Matters to be known as the manager of automatic feeding mixer truck
自动上料搅拌车操作者需要经过相关的培训,熟悉其操作规则。小编认为,作为自动上料搅拌车操作者您需要做好以下四个方面工作。
The operator of automatic feeding mixer truck needs to be trained and familiar with its operation rules. Xiaobian believes that as an operator of automatic feeding mixer truck, you need to do the following four aspects.
一、预防混凝土粘罐。在施工现场卸料完毕后,应立即用搅拌车随带的软管冲洗进料斗、出料斗、卸料熘槽等处,清理粘附在车身各处的污泥及混凝土。在返回搅拌站的途中,应向搅拌筒内注150---200L水以清洗筒壁及叶片粘结的混凝土残渣。每天工作结束后,司机应负责向搅拌筒内注入清水并高速(14—18转/分)旋转5—10分钟,然后将水排去,以保证筒内清洁。用高压水清洗搅拌筒各个部分时,应注意避开仪表及操纵杆等部位。压力水喷嘴与车身油漆表面间的距离不得小于40厘米。
1、 Prevent concrete from sticking to the tank. After unloading at the construction site, immediately flush the inlet hopper, outlet hopper and unloading chute with the hose attached to the mixer truck, and clean the sludge and concrete adhered to the vehicle body. On the way back to the mixing plant, 150-200l water shall be injected into the mixing drum to clean the concrete residue bonded to the drum wall and blades. At the end of each day's work, the driver shall be responsible for injecting clean water into the mixing drum and rotating at high speed (14-18 RPM) for 5-10 minutes, and then drain the water to ensure the cleanness of the drum. When cleaning all parts of the mixing drum with high-pressure water, pay attention to avoid instruments, control rods and other parts. The distance between the pressure water nozzle and the paint surface of the vehicle body shall not be less than 40cm.
自动上料搅拌车厂家
Automatic feeding mixer manufacturer
二、清洁工作。清理搅拌筒内外积污及残存的混凝土渣块时,以及在机修人员进入筒内进行检修和焊补作业时,需先关闭汽车发动机,使搅拌筒完全停止转动。在机修人员进入筒内工作期间,须保证拌筒内通风良好,空气新鲜,无可然气体及有害灰尘,氧气供应充足。在筒内使用电动工具操作时,操作人员须有良好的绝缘保护。
2、 Cleaning work. When cleaning the dirt and residual concrete slag inside and outside the mixing drum, and when the mechanical maintenance personnel enter the drum for maintenance and welding repair, it is necessary to turn off the automobile engine first to stop the mixing drum completely. During the working period when the mechanical maintenance personnel enter the drum, they must ensure that the mixing drum is well ventilated, the air is fresh, there is no combustible gas and harmful dust, and the oxygen supply is sufficient. When using electric tools in the cylinder, the operator must have good insulation protection.
三、防护工作。在自动上料搅拌车工作时,不得将手伸入旋转的搅拌筒内,严禁将手伸入主卸料熘槽和加长卸料熘槽的连接部位,以免发生事故。
3、 Protection work. When the automatic loading mixer works, do not put your hand into the rotating mixing drum, and do not put your hand into the connecting part of the main unloading frying groove and the extended unloading frying groove, so as to avoid accidents.
四、液压系统压力应符合使用说明书中的规定,不得随意调整。液压油的油质和油量应符合原定要求。
4、 The pressure of the hydraulic system shall comply with the provisions in the operation manual and shall not be adjusted at will. The oil quality and quantity of hydraulic oil shall meet the original requirements.
以上就是为大家介绍的有关自动上料搅拌车的详细介绍,希望对您有所帮助.如果您有什么疑问的话,欢迎联系我们.我们将以的态度,为您提供服务http://www.shanqijituan.com/
The above is a detailed introduction to the automatic feeding mixer truck. I hope it will be helpful to you If you have any questions, please contact us We will provide you with professional service http://www.shanqijituan.com/
热门产品 / HOT PRODUCT

 

首页 产品 电话 置顶